| Pegazusoa-` | This channel has be subscribed the S uper N e Ts Radio Hour! Dial 1-877-293-1933 to unsubscribe! | 05:58 |
|---|---|---|
| Pegazusoa-` | Pegazusoa-` parazyd LIERO branon Langoor lightbri1ger dsc__ nohit noidea__ Evil_Bob_ [TheBug] jrayhawk_ jesster1234 bencoh_ nela f_ akossh RedW joerg Madda LeePen ungeskriptet xes n900 eval pere Juest danielinux inky Rodney_ ikmaak gnarface narodnik doc _whitelogger hexnewbie xs LjL crab retr0id durrendal Danct12 nerdcore kona Oksana Armen brabo mn3monic jr-logbot DPA wuboy sch f_[xmpp] Blikje | 05:58 |
| tmlind | freemangordon: hmm looks like pinephone also needs to use at interface for voice calls in addition to qmi: https://lore.kernel.org/ofono/2269874.vFx2qVVIhK@adam-laptop-hp/ | 06:56 |
| tmlind | also because of lost qmi events | 06:56 |
| tmlind | ok looks like the lcd bridge changes got merged, so i should send the mz61x lcd dts patches after -rc1 too | 07:10 |
| freemangordon | tmlind: hmm, could this be some general USB issue? | 08:25 |
| tmlind | freemangordon: could be some usb wakeup issue on the qmi in the pinephone case, however on d4 we never get the qmi events without kicking the qmi | 08:36 |
| freemangordon | tmlind: right, but that does not mean it is not usb issue | 09:48 |
| freemangordon | because I don;t get usb events occasionally with quectel as well | 09:49 |
| freemangordon | when connected to the VM that is | 09:49 |
| freemangordon | when connected to may laptop with 5.15, I cannot enable PM for that device at all | 09:49 |
| freemangordon | so there is something fishy as I see it | 09:50 |
| freemangordon | *my laptop | 09:50 |
| tmlind | ok sounds like the linux kernel qmi usb device driver does not properly support usb wakeups, or the firmware is buggy on the modem and not doing the usb wakeup events | 10:00 |
| tmlind | the usb wakeup event is just some pull on one of the data lines if i remember correctly, if the usb phy does not see the event also the usb phy device driver could buggy or idle and unable to see it | 10:01 |
| freemangordon | yes, looks like that | 10:02 |
| freemangordon | FW issue perhaps, as otherwise lots of devices would have the same issues (mice, kbd, etc) | 10:03 |
| freemangordon | but can;t be proven without having equipment I don't have :) | 10:04 |
| freemangordon | Wizzup: do we support https://telepathy.freedesktop.org/spec/Channel_Type_Text.html#Method:AcknowledgePendingMessages on conversations? | 10:07 |
| Wizzup | hello | 12:59 |
| Wizzup | freemangordon: I will take a look at this | 12:59 |
| Wizzup | freemangordon: I think we do | 13:00 |
| Wizzup | See channel->acknowledge(messages); | 13:00 |
| Wizzup | phoenix is just down momentarily while I figure something out | 14:59 |
| Wizzup | fyi | 14:59 |
| Wizzup | (also leste.maemo.org) | 15:22 |
| Wizzup | (all fixed) | 16:03 |
| Wizzup | uvos: let's also try to do more than one voice call and see if it starts working as tmlind said | 16:03 |
| Wizzup | freemangordon: dsc__: so the line to actually open the window was commented | 17:29 |
| Wizzup | in conversations | 17:29 |
| Wizzup | pushing a fix now | 17:29 |
| Wizzup | it's fixed now fwiw | 19:15 |
| Wizzup | at least for me | 19:15 |
| arno11 | freemangordon: i think i found the problem for ringtones. PA seems the culprit: nokia ringtones from /usr/share are @11025Hz apparently so they can only be played with PA default sample rate @44100 (actually 48000 on N900 to get calls working @4000Hz) | 19:31 |
| arno11 | so that's probably why mp3's (44100Hz) from MyDocs work (because alternate sample rate is currently 44100) | 19:33 |
| arno11 | *mp3 ringtones | 20:01 |
| arno11 | so it makes sense if default ringtone works on D4 (default sample rate is @44100) | 20:03 |
| arno11 | iirc PA can use any multiple of the default sample rate but NOT from the alternate | 20:06 |
| arno11 | and...i'm wrong lol: i'm able to use Nokia ringtones if i move them in MyDocs | 20:15 |
| arno11 | really weird stuff, maybe only a permission issue (?) | 20:18 |
| Wizzup | will check this in a bit | 20:22 |
| dsc__ | i think both my d4's are just really drained | 20:23 |
| dsc__ | cant boot them | 20:23 |
| dsc__ | it was on power outlet for 1 month | 20:23 |
| dsc__ | :P | 20:23 |
| dsc__ | which seems to indicate it wont charge too | 20:24 |
| Wizzup | I'll help you get this fixed | 20:27 |
| Wizzup | maybe tomorrow? | 20:27 |
| Wizzup | one thing to check is if you can still get to fastboot | 20:27 |
| Wizzup | (hold power + vol min) | 20:27 |
| Wizzup | (that's the volume button that is the furtherst away from the power button) | 20:27 |
| dsc__ | is fastboot something different from kexecboot? | 20:27 |
| Wizzup | you can do this while it's connected | 20:27 |
| Wizzup | fastboot is what we can use to flash a new kexecboot | 20:27 |
| dsc__ | the menu looks the same, so there are other options with fashboot? | 20:28 |
| dsc__ | fastboot* | 20:28 |
| dsc__ | what should I pick? | 20:28 |
| Wizzup | what do you see | 20:28 |
| dsc__ | i already tried this btw, I think I picked 'stock android' but after picking that, nothing happens | 20:29 |
| dsc__ | and sometimes the fastboot wont even come up at all | 20:29 |
| dsc__ | (after power + vol min) | 20:29 |
| dsc__ | like right now | 20:29 |
| Wizzup | so fastboot won't show 'stock android' | 20:29 |
| Wizzup | that's a separate thing | 20:29 |
| dsc__ | alright | 20:30 |
| dsc__ | then im not getting into fastboot | 20:30 |
| Wizzup | you need to press that like briefly, just one second or so | 20:30 |
| Wizzup | what charger are you using? | 20:30 |
| dsc__ | ok from the start: | 20:30 |
| Wizzup | what's the amp | 20:30 |
| dsc__ | d4 is connected to USB charger | 20:30 |
| dsc__ | green light comes up | 20:30 |
| dsc__ | but only one 1 droid4, the other doesnt show anything | 20:30 |
| dsc__ | as in, doesnt show the green lighjt | 20:31 |
| dsc__ | so | 20:31 |
| dsc__ | power hold + vol min = nothing happens (But after 7sec the light goes off) | 20:31 |
| Wizzup | yes, that is the hard reset | 20:31 |
| Wizzup | Start the device in fastboot mode. For this press power button and bottom volume key simultaneously and release them after a second. | 20:31 |
| Wizzup | (from the wiki) | 20:31 |
| Wizzup | does that do anything? | 20:31 |
| dsc__ | < dsc__> power hold + vol min = nothing happens (But after 7sec the light goes off) | 20:32 |
| Wizzup | I think we need to do this over a video meet when I get back | 20:32 |
| Wizzup | that will make the communication easier | 20:32 |
| dsc__ | to get into fastboot mode I need to do "power hold + vol min" for 7 seconds right? | 20:33 |
| dsc__ | im doing that, nothing happens :) | 20:33 |
| Wizzup | I did read what you said, but you need to run fastboot when it is not showing a green light, maybe with the cable out, or at least after you hard shut it off | 20:33 |
| Wizzup | no, I literally pasted from the wiki that it is a single second | 20:33 |
| Wizzup | what's the amperage on your psu? | 20:33 |
| sicelo | dsc__: completely power off the device first | 20:33 |
| dsc__ | ok | 20:34 |
| dsc__ | sicelo: and then with no cable connected, I press 'power btn + vol min' for 1 sec | 20:34 |
| dsc__ | nothing happens | 20:34 |
| Wizzup | you can do it with the cable connected I think, but you need to do the 7 seconds full power down first, but yeah, try without | 20:34 |
| dsc__ | yeah, nothing | 20:35 |
| Wizzup | ok, please look up the amperage on your usb power supply | 20:35 |
| dsc__ | 9.0V == 1.67A 15W | 20:36 |
| dsc__ | 5.0 == 2.0 A 10W | 20:36 |
| dsc__ | 5.0v | 20:36 |
| Wizzup | wait what's the 9V? | 20:36 |
| dsc__ | it says it outputs 9V or 5V, idk | 20:37 |
| Wizzup | is this the one I that I bought last year? | 20:37 |
| dsc__ | no | 20:37 |
| Wizzup | do you have any other usb wall chargers? | 20:37 |
| sicelo | dsc__: completely powered off. then, just hold the vol down (key furthest from Motorola logo), and hold power button. when you let them go, you should be in fastboot mode | 20:37 |
| dsc__ | found another one, its 5v 4.8a 24w | 20:38 |
| Wizzup | sicelo: yes but his battery is very low | 20:38 |
| Wizzup | dsc__: wow, that's a lot, is that a regular usb wall charger? | 20:38 |
| Wizzup | for a rpi or something? | 20:38 |
| dsc__ | im not sure where this came from | 20:38 |
| dsc__ | possibly you bought it yeah | 20:38 |
| Wizzup | I bought one with 4 output ports on it | 20:38 |
| Wizzup | white or black | 20:38 |
| dsc__ | right | 20:38 |
| dsc__ | its this one | 20:38 |
| dsc__ | is it a fire hazard ^^ ? | 20:39 |
| Wizzup | pa0221w? | 20:39 |
| Wizzup | no I think it's fine | 20:39 |
| dsc__ | yeah | 20:39 |
| Wizzup | maybe hook one of the droid4 up to this one while I go to the shop | 20:39 |
| dsc__ | without the 'w' | 20:39 |
| Wizzup | we cna pick it up afterwards | 20:39 |
| sicelo | if they get to kexecboot, they should be able to get into fastboot. anyway, maybe making buzz's USB condom is quickest way to recover from lowbat | 20:39 |
| Wizzup | w for white I suppose | 20:39 |
| dsc__ | :P | 20:39 |
| dsc__ | sicelo: ok, ill try | 20:40 |
| dsc__ | sicelo: the only way I can get into kexecboot is by attaching the device to power, at which it automatically starts booting | 20:41 |
| dsc__ | but after pressing the Leste option, it shuts down | 20:41 |
| dsc__ | anyway, 'pwr btn + min vol' is not working | 20:41 |
| dsc__ | Re sicelo's guiode | 20:41 |
| dsc__ | guide | 20:41 |
| dsc__ | ill try this new USB charger. | 20:42 |
| sicelo | rather try the condom ... it's no longer a matter of chargers :-p | 20:42 |
| dsc__ | Wizzup: btw, when I get the new image, does that already have some power improvements? | 20:42 |
| dsc__ | or do I actually need to flash something? | 20:42 |
| dsc__ | like update kexecboot | 20:43 |
| dsc__ | sicelo: ? | 20:43 |
| dsc__ | oh I got into fastboot just now | 20:43 |
| Wizzup | newer kexecboot is able to charge | 20:43 |
| sicelo | dsc__: 20:39 < sicelo> ...maybe making buzz's USB condom is quickest way to recover from lowbat | 20:44 |
| Wizzup | https://github.com/tmlind/droid4-kexecboot/commit/4f2c742395cb390ed690ae8bbe480ed1c1b0fb88 | 20:44 |
| dsc__ | ah thanks | 20:44 |
| Wizzup | just leave fastboot running with the device on the power supply for now | 20:44 |
| Wizzup | that can't hurt | 20:44 |
| dsc__ | ok cool | 20:44 |
| Wizzup | afaik | 20:44 |
| dsc__ | just to clarify, since I can get into fastboot now, I can now update kexecboot, which will give some charging improvements? | 20:45 |
| Wizzup | yes but no | 20:45 |
| Wizzup | fastboot needs sufficient power to allow you to flash | 20:45 |
| dsc__ | ah | 20:45 |
| dsc__ | fastboot says the battery is 'low' :D | 20:47 |
| dsc__ | it aint lying | 20:47 |
| Wizzup | just leave it like this for a bit, or just with the screen off green light mode, I am pretty confident just leaving it like this for a while using the port charger will make it work | 20:49 |
| Wizzup | I've never had to resort to special methods to resurrect these things | 20:49 |
| Wizzup | but the charger matters | 20:49 |
| Wizzup | it's possible that your 5v/9v one provides very little unless there's some proper negotiation being done | 20:49 |
| dsc__ | gotcha | 20:50 |
| dsc_ | Wizzup: my d4 with Leste on it, doesnt show the green light when connected to power | 21:13 |
| dsc_ | is it still charging? | 21:13 |
| freemangordon | Wizzup: ok, thanks | 21:22 |
| freemangordon | Wizzup: are you still able to dial a contact from addressbook of from desktop contact? | 21:24 |
| dsc_ | Wizzup: nvm, got it all working now. So probably charging related. | 21:33 |
| dsc_ | charger* | 21:33 |
| dsc_ | great :) | 21:33 |
| sicelo | nice | 21:36 |
| Wizzup | freemangordon: I will try @ dialing | 21:43 |
| Wizzup | dsc_: so both are charging? | 21:43 |
| dsc_ | have not tried the other yet | 21:44 |
| dsc_ | im going to buy a SIM card soon and actually use d4 as a proper phone | 21:44 |
| Wizzup | :) | 21:45 |
| freemangordon | Wizzup: we don;t have TP handler for channel type org.freedesktop.Telepathy.Channel.Type.Call1 | 21:50 |
| freemangordon | https://pastebin.com/TtH46iCY | 21:52 |
| Wizzup | freemangordon: ok, so that is needed for sphone vcm | 22:04 |
| sicelo | Wizzup: upgrading kexecboot on existing installation is just `sudo fastboot flash bpsw droid4-kexecboot.img`? or another command needed too? | 22:15 |
| Wizzup | yes, I think that is all you need | 22:20 |
| sicelo | i'll try it. hope nothing breaks | 22:21 |
| dsc_ | ill wait for you to try before doing it myself :D | 22:21 |
| Wizzup | I just flashed the current one to three droid4's the other day | 22:22 |
| sicelo | worked... at least Leste still boots | 22:38 |
| buZz | 20:42:46 < sicelo> rather try the condom ... it's no longer a matter of chargers :-p | 23:49 |
| buZz | yeah, works well, on many different devices :) | 23:49 |
Generated by irclog2html.py 2.17.0 by Marius Gedminas - find it at https://mg.pov.lt/irclog2html/!